Ideal camera output
Noisy camera output
Visibility, transfer, I₊/I₋ / D / Teff, profiles, histograms, residual, and A–D bars + camera strip (NF/FF · T/R). Use ⛶ to enlarge any plot.
Visibility & thermal
Effective transfer Teff / φeff
A–D comparison (V / mean)
A–D camera strip (Ideal / Noisy)
Use ⛶ above each frame to enlarge that image.
Line profiles (SLM / ideal / noisy)
Intensity histograms
Ideal − noisy residual
Plus port I₊
Minus port I₋
Difference port D = I₊ − I₋
Teff map
Ideal → Optics → Drift → Shot/Read → Detector → Full. Image strip, Δ-to-ideal KPIs, and SNR / V / RMS bars.
Click “Run stage ladder” for Ideal → Optics → Drift → Shot/Read → Detector → Full.
Stage KPI bars
Mechanism matrix, four-step phase maps, I(φ) fringe curve, and one-parameter metric sweeps.
Run a lab diagnostic to populate the matrix, phase maps, fringe curve, or sweep.
Phase map φ(x, y)
Phase modulation / fringe contrast
I(φ) fringe curve
Sweep curve (relative % vs first point)
Highest-value twin teaching surfaces wired for local release (orchestration only — no new physics).
- A–D arrangements with NF/FF · T/R captions
- Ideal / noisy forward images + SNR · V · residual KPIs
- Line profiles, histograms, residual, D-port, I₊/I₋, Teff
- A–D V bars + Ideal/Noisy camera strip
- Noise stage ladder + mechanism ablation matrix
- Four-step phase maps + I(φ) fringe curve with Michelson V
- One-parameter metric sweeps (relative %)
- Lens rings / etalon / focus–Δz bridges for visible optics knobs
- Out of scope for this release: knife-edge MTF, Fig.6 C-lab rings, dataset export, photon-counting mode
Prototype / pre-validation UI. These notes document web behavior without changing the physics engine.
Color scale. Each PNG is normalized to its own min–max (no shared colorbar). Compare intensities via the numeric mean/min/max under each tile, not by color alone. Ideal uses arb. photon-like units; noisy uses detector counts (bias + EM gain).
Frame count N. The “Frame count N” control is the acquisition schedule length, not a √N shot-noise averager.
Crystal temperature. Tpm0/ΔT are UI set-points. Small offsets may look nearly flat in the camera tiles depending on the active twin mapping.
Pump waist & far field. The web slider syncs NL1/NL2 waists. Far-field tiles can look flat for uniform objects; relay magnifications on Geometry apply to arrangement A only (not C).
Drift knobs. Several s_* latents are weakly visible at default short exposures; raise exposure / n̄ / frames together when exploring them.
Ideal vs noisy source. Separate tabs store different defaults (n̄, exposure, EM gain, N). Ideal is a clean forward map; noisy includes drift + EMCCD path — units differ by design.
Visibility & brightness. Ideal low-n̄ contrast is typically well below 100% (interference / mode factors). Default n̄ can sit above the classical ultra-low-flux QIUP regime; use the n̄ slider for low-flux studies.
Far-field magnification. Reported geometric mag. can differ from a simple λs/λi thin-lens estimate if relay definitions absorb wavelength factors — treat relay sliders as UI geometric controls for A.
Stop. Stop aborts the browser stream only; an in-flight server job may still finish.
Press Run simulation or Ctrl+Enter.
This application was developed at the Center for Innovation and Development of Artificial Intelligence Technologies, University of Isfahan.
- Fateme Haji Shafiee
- Atefeh Khaki Bakhtiarvand
- Arash Rayan
- Mohammad Zakaria Rajabi
- Hamid Reza Mohammadi
- Hamid Reza Marateb
- Rasoul Roknizadeh